ImmersionRC Tramp/Ghost Hybrid UNO V2 2.4GHz Rx & 25-600mW 5.8GHz VTX
| Manufacturer: |
|
| Model: | irc_tramp/ghost_hybrid_uno_v2 |
|
|
|
Description
About this product
The new ImmersionRC Tramp/Ghost Hybrid UNO V2 is a high-end analog 5.8GHz 25mW - 600mW video transmitter and 2.4GHz diversity receiver!
There is nothing like the experience of flying an FPV drone, but building these marvelous machines is more complex than it needs to be. With Tramp, ImmersionRC has set out to raise the bars on video transmitter technology. With Ghost, ImmersionRC has set out to redefine the norms in receivers for R/C control. And now ImmersionRC has fused these two together in the groundbreaking Ghost Hybrid. Designed by pilots, built by pilots, supported by pilots.
Features
20 x 20mm Mounting
Single-sided PCB with gummies included
Only 2.2g, perfect for the sub-250g class
Long-range AND low latency
250Hz updates
2.4GHz LoRa and FLRC Control
5.8GHz 1-600mW Video Transmitter
All 48 Standard Channels
Thermally regulated, Factory calibrated
500Hz/1kHz ready for when OpenTx can supply quality data at this rate
Available vTx channels and power may vary from region to region to comply with local regulations
2.4GHz ISM Band
Tiny 15 x 12mm, and 0.61g
Crazy Race Performance, 222.22Hz updates (500Hz Ready)
4ms End to End Latency (2ms ready), with OpenTx Integration
Fully supported by Betaflight with GHST driver
Specifications
Downlink RF Power: +13dBm
Sensitivity: -117dBm in Long Range mode
Serial Formats: GHST, SBus, SBus-Fast (200k), SRXL-2 (400k), SBus Inverted
Firmware: Over-the-air (OTA) upgradeable (Rx and VTx)
Power Supply: 5V, with Over Voltage Protection
VTX Control: Automatic, via Ghost
Antenna Connectors: Standard U.FL with Locking Connectors
Dimensions: 26mm x 126mm, 2.2g (w/o antennas)
Intelligent VTX Control
Intelligent, and direct control of the video transmitter from the Ghost ecosystem. Use either the OLED menus on the Ghost Transmitter module or the responsive OpenTx tools menu. Tx remains silent on power-up, shuts down immediately in an (unlikely) failsafe.
Locking Connectors
Innovative locking connectors deliver the advantages of the lightweight u.FL/MHF standard, with the security required for world-class racing, or long-range flying. Simply plug the connector onto the board, and slide the locking cap to secure.
Thermal Regulation + Calibration
As with all tramp products, the Hybrid includes automatic thermal regulations, protecting the video transmitter against potentially damaging overheating while sitting on the starting pad. The onboard Tramp is factory calibrated, for precise power delivery during critical race events.
qTee Antennas
qTee, a.k.a ‘Cutie’ antennas are center-fed dipoles, with integral balun to ensure no cable radiation, and without unexpected nulls in the radiation pattern. Tip to Tip length of just 60mm, easy to install in anything from a Whoop™ to an X-Class quad
Manual
Firmware/ Downloads
Parameters
| Antenna connector | IPEX (u.FL) |
| Dimensions (Length * Width * Height) | 26x26 mm |
| Input voltage | 5 Volts |
| Mounting pattern | 20x20 mm (micro) |
| Radio frequency | 5.8 GHz |
| Weight | 2,2 g |
Package included
1 x ImmersionRC Tramp/Ghost Hybrid UNO V2 2.4GHz Rx & 25-600mW 5.8GHz VTX
1 x Silicone Cable
2 x qTee Antenna